Di-Acro Model 6 Tube and Pipe Bender

Model 6 Setup - For bending TUBING, ANGLE AND CHANNEL. Includes clamps and pressure roller assembly as basic tooling for tube bending. Standard Grooved Radius Collar - For bending round tubing. Used with Clamp Block and Follow Block. When bending materials of open cross section such as tubing, channel, angle and extrusions, the bending form should exactly fit the contour of the material to provide support during the forming operation. This is also true of the Clamp Block and Pressure Tool as only completely confining the material can a good bend be obtained. Special Crush Bend Tooling for Round and Square Tubing - designed for both 6 POWER and 8 POWER benders. Crush bend tooling is used primarily for bending thin wall tubing to a tight radius. If it is not necessary for the formed section to retain its original shape, such as in structural components, the tubing can be uniformly indented with this tooling. The "crush" on the inside radius adds additional strength to the bend, as well as allowing a tight radius with controlled distortion in the bend area.

Di-Acro Model 8 Tube and Pipe Bender

Model 8 Setup - For bending SOLID STOCK. Especially suitable for bending eyebolts with centered or off-centered eye bends in one operation. Built Up Forming Nose - Forms wider materials with special height or stacked collars. •Radius Block - For forming solid materials to a tight radius. Requires a standard locking pin to hold material. •Radius Collar - Forms solid stock to larger radii. Requires standard locking pin to hold material. •Forming Roller - Replaces forming nose to eliminate part marking. •Radius Pins - Shoulder Radius Pin is used for forming solid materials to a larger radius. A Quill Radius pin is used for forming light material to a tight radius. Both pins require a standard locking pin to hold material in place.

Di-Acro Model 1 Tube and Pipe Bender

The Di-Acro Bender is a multi-purpose machine that quickly adapts to a variety of bending operations, whether prototype, production or for duplicating parts with simple, compound or reverse bends in many materials — angle, channel, tubing, rod wire, strip stock, ect. They are die substitutes that also produce work not obtainable with dies. The Hand Bender is available in five models with capabilities of bending up to 1in round mild steel bar with a radius of 0 - 12in. The Model 4 Bender features a selectable ratchet drive mechanism for increased power when working with heavier materials.

Di-Acro Model 1A Tube and Pipe Bender

The Di-Acro Bender is a multi-purpose machine that quickly adapts to a variety of bending operations, whether prototype, production or for duplicating parts with simple, compound or reverse bends in many materials — angle, channel, tubing, rod wire, strip stock, ect. They are die substitutes that also produce work not obtainable with dies. The Hand Bender is available in five models with capabilities of bending up to 1in round mild steel bar with a radius of 0 - 12in. The Model 4 Bender features a selectable ratchet drive mechanism for increased power when working with heavier materials.

Di-Acro Model 2 Tube and Pipe Bender

The Di-Acro Bender is a multi-purpose machine that quickly adapts to a variety of bending operations, whether prototype, production or for duplicating parts with simple, compound or reverse bends in many materials — angle, channel, tubing, rod wire, strip stock, ect. They are die substitutes that also produce work not obtainable with dies. The Hand Bender is available in five models with capabilities of bending up to 1in round mild steel bar with a radius of 0 - 12in. The Model 4 Bender features a selectable ratchet drive mechanism for increased power when working with heavier materials.

Di-Acro Model 3 Tube and Pipe Bender

The Di-Acro Bender is a multi-purpose machine that quickly adapts to a variety of bending operations, whether prototype, production or for duplicating parts with simple, compound or reverse bends in many materials — angle, channel, tubing, rod wire, strip stock, ect. They are die substitutes that also produce work not obtainable with dies. The Hand Bender is available in five models with capabilities of bending up to 1in round mild steel bar with a radius of 0 - 12in. The Model 4 Bender features a selectable ratchet drive mechanism for increased power when working with heavier materials.

Di-Acro Model 4 Tube and Pipe Bender

The Di-Acro Bender is a multi-purpose machine that quickly adapts to a variety of bending operations, whether prototype, production or for duplicating parts with simple, compound or reverse bends in many materials — angle, channel, tubing, rod wire, strip stock, ect. They are die substitutes that also produce work not obtainable with dies. The Hand Bender is available in five models with capabilities of bending up to 1in round mild steel bar with a radius of 0 - 12in. The Model 4 Bender features a selectable ratchet drive mechanism for increased power when working with heavier materials.

Di-Acro Model 24 Brake

Di-Acro Finger Brakes lend versatility and accuracy to the forming of angles, channels, flanges, Vees and box parts with speed and precision. Readily adaptable for prototyping and production runs on many intricate and special shapes in sheet metal. Di-Acro Finger Brakes are adjustable to enable precision bending by compensating for material thickness and hardness. Box finger segments enable the operator to form boxes from 3/4in up to the full width capacity of the machine in increments as small as 1/4in. Model 24 includes: 2 - 3/4, 2 - 1, 2 - 1 1/4, 2 - 3, and 2-6 inch box fingers.

Di-Acro Model 36 Brake

Di-Acro Finger Brakes lend versatility and accuracy to the forming of angles, channels, flanges, Vees and box parts with speed and precision. Readily adaptable for prototyping and production runs on many intricate and special shapes in sheet metal. Di-Acro Finger Brakes are adjustable to enable precision bending by compensating for material thickness and hardness. Box finger segments enable the operator to form boxes from 3/4in up to the full width capacity of the machine in increments as small as 1/4in. Model 36 includes: 2 - 3/4, 2 - 1, 2 - 1 1/4, 2 - 3, and 4 - 6 inch box fingers.

Di-Acro Model 12 Shear

Di-Acro Hand Shears offer precision shearing at an economical price. Utilizing overdriven leverage, they are ideal for useon light and medium weight sheet metal, plastics, rubber, fabric, leather, synthetics, dielectrics and various other materials.Well suited to prototype shops and short run production operations.

Di-Acro Model 24 Shear Shear

Di-Acro Hand Shears offer precision shearing at an economical price. Utilizing overdriven leverage, they are ideal for useon light and medium weight sheet metal, plastics, rubber, fabric, leather, synthetics, dielectrics and various other materials.Well suited to prototype shops and short run production operations.

Di-Acro Model 2 Notcher Notcher

The Di-Acro Tab Notcher is a versatile, heavy-duty tool which cuts any size notch to 6in x 6in with any size tab to 1in in one operation. Both upper and lower cutting blades are adjustable to give you any size and depth, regular or tab notch combination, within the capacity of the machine. Overlapping tabs can be easily spot-welded to produce chassis and boxes with greater strength.

Di-Acro Model 12 Slip Roll Slip Roll

Di-Acro Slip Rollers feature a cam-actuated idler roll which permits the operator to locate bends at any point along a sheet of material with straight sections on one or both ends. The idler roll always returns to its present position, allowing duplication with a high degree of accuracy. Calibrated rear roll indicators enable the operator to quickly adjust the machine when changing from one rolling size to another. Small circles, approximately the same diameter as the forming rolls, can be produced in one operation. Circles of any larger diameter can be created in just two passes through the rolls. Round, flat, square and other materials can be formed with Di-Acro Rollers by grooving the bending rolls to fit the shape of the material. Grooving must be specified at time of order. Flat Material: Flat material can be rolled part way through the rolls (Illustration A) and when the cam lever is engaged, the idler roll is raised and a bend is formed. Disengaging the cam lever lowers the idler roll, and the material again passes through the rolls in a horizontal or flat position. It is thus possible to form a wide variety of shapes with the Di-Acro Roller.

Di-Acro Model 24 Slip Roll Slip Roll

Di-Acro Slip Rollers feature a cam-actuated idler roll which permits the operator to locate bends at any point along a sheet of material with straight sections on one or both ends. The idler roll always returns to its present position, allowing duplication with a high degree of accuracy. Calibrated rear roll indicators enable the operator to quickly adjust the machine when changing from one rolling size to another. Small circles, approximately the same diameter as the forming rolls, can be produced in one operation. Circles of any larger diameter can be created in just two passes through the rolls. Round, flat, square and other materials can be formed with Di-Acro Rollers by grooving the bending rolls to fit the shape of the material. Grooving must be specified at time of order. Flat Material: Flat material can be rolled part way through the rolls (Illustration A) and when the cam lever is engaged, the idler roll is raised and a bend is formed. Disengaging the cam lever lowers the idler roll, and the material again passes through the rolls in a horizontal or flat position. It is thus possible to form a wide variety of shapes with the Di-Acro Roller.