Everett 10-WC Wet Cut-off Saw

Complete with 3 HP TEFC motor, coolant tray, magnetic starter with 110 volt at the pushbuttons, steel stand, settling tank and pump Ideal For METALLURGICAL LABS as well as for Exotic Alloys. Typical wet cutting speeds are 30 seconds per square inch of material based on application. Capacity: 1in solids and 2in shapes. Coolant flow can be regulated and directed to both sides of the cut for optimum performance.

Everett 10-WC-Miter Wet Cut-off Saw

Complete with 3 HP TEFC motor, coolant tray, magnetic starter with 110 volt at the pushbuttons, steel stand, settling tank and pump Ideal For METALLURGICAL LABS as well as for Exotic Alloys. Typical wet cutting speeds are 30 seconds per square inch of material based on application. Capacity: 1in solids and 2in shapes. Coolant flow can be regulated and directed to both sides of the cut for optimum performance.

Everett 12 Abrasive Cut-off Saw

Complete with 5 HP TEFC motor, magnetic starter with 110 volt at the pushbuttons, steel stand, V shaped chain hold-down vise Fast, Low Cost Cutting of Hardened Tool Steel, Bars, Pipe, Angle Iron, Tubing, Flat Stock & Rod. Ideal for use in manufacturing Golf Club Shafts. Capacity: 1.75in solid. 3in pipe

Everett 12-Miter Miter Cut-off Saw

Complete with 5 HP TEFC motor, magnetic starter with 110 volt at the pushbuttons, steel stand, V shaped chain hold-down vise Fast, Low Cost Cutting of Hardened Tool Steel, Bars, Pipe, Angle Iron, Tubing, Flat Stock & Rod. Ideal for use in manufacturing Golf Club Shafts. Capacity: 1.75in solid. 3in pipe

Everett 14-16 Abrasive Cut-off Saw

Complete with 7 1/2 or 10 HP TEFC motor, magnetic starter with 110 volt at the pushbuttons, steel stand, V vise Fast Cutting of Hardened Tool Steel, Bars, Pipe, Angle Iron, Tubing, Flat Stock & Rod. Capacity: 2in solid. Most 5in shapes

Everett 14-16-DMiter Abrasive Cut-off Saw

Complete with 7.5 or 10 HP TEFC motor, magnetic starter with 110 volt at the pushbuttons, air operated dual chain hold-down vise Fast, Low Cost Cutting of Hardened Tool Steel, Drills, Reamers, Bars, Pipe, Angle Iron, Tubing, Flat Stock & Rod. Capacity: 2in solid • 5in pipe 30°-45°—1.75in Solids • 3in Most Shapes Double Mitering Cutting Head can swivel 45° right or left of center. Indicators for 0°, 15°, 30° and 45°. Cutting head and pedestal are mounted on rugged swinging knee secured in lubricated for life bearings. Lock to hold desired cutting angle is quick and easy to operate.

Everett 14-16-Hydraulic Abrasive Cut-off Saw

Complete with 7.5 or 10 HP TEFC motor, magnetic starter with 110 volt at the pushbuttons, steel stand, V vise Capacity: Up to 5in Wire Braid & Spiral Reinforced Hoses Including Thermoplastic Hoses

Everett 14-16-Miter Abrasive Cut-off Saw

Complete with 7.5 or 10 HP TEFC motor, magnetic starter with 110 volt at the pushbuttons, steel stand, V vise Capacity: Up to 5in Wire Braid & Spiral Reinforced Hoses Including Thermoplastic Hoses

Everett Everett_14-16W Wet Cut-off Saw

Complete with 7.5 or 10 HP TEFC motor, magnetic starter with 110 volt at the pushbuttons, steel stand, V vise Capacity: Up to 5in Wire Braid & Spiral Reinforced Hoses Including Thermoplastic Hoses

Everett Everett_14-22 Abrasive Cut-off Saw

Complete with magnetic starter with 110 volt at the pushbuttons, V shaped chain hold-down foot pedal operated vise This machine is built so that heavy wire rope does not have to be lifted to normal table height. The machine is equipped with casters to make location change easy and a foot pedal operated chain hold-down vise to securely hold the wire rope while it is being cut.

Everett Everett_20-22C Abrasive Cut-off Saw

Complete with 7.5 or 10 HP TEFC motor, magnetic starter with 110 volt at the pushbuttons, V shaped chain hold-down vise, steel stand For Cutting Up to 6in Pipe and Conduit This rugged, but portable, Everett model was specially designed for the job site. The Contractors Model comes complete with magnetic starter with 110 volt at the pushbutton, stand and foot pedal operated vise. The special high-torque motor is totally enclosed and fan cooled.

Everett Everett_20-22 Abrasive Cut-off Saw

Complete with 7.5 or 10 HP TEFC motor, magnetic starter with 110 volt at the pushbuttons, V shaped chain hold-down vise, steel stand For Cutting Up to 6in Pipe and Conduit This rugged, but portable, Everett model was specially designed for the job site. The Contractors Model comes complete with magnetic starter with 110 volt at the pushbutton, stand and foot pedal operated vise. The special high-torque motor is totally enclosed and fan cooled.

Everett Everett_20-22DM Abrasive Cut-off Saw

Complete with 10 or 20 HP TEFC motor, magnetic starter with 110 volt at the pushbuttons, cabinet base, air-operated dual chain hold-down vise. Fast, Low Cost Cutting of Hardened Tool Steel, Bars, Pipe, Angle Iron, Tubing, Flat Stock & Rod. Capacity: 3in solid • 6in Most Shapes • 30°- 45°—2.5in Most Solids • 4in Most Shapes Double Mitering Cutting Head can swivel 45° right or left of center. Indicators for 0°, 15°, 30° and 45°. Cutting head and pedestal are mounted on rugged swinging knee secured in lubricated for life bearings. Lock to hold desired cutting angle is quick and easy to operate.

Everett Everett_20-22M Abrasive Cut-off Saw

Complete with 10 or 20 HP TEFC motor, magnetic starter with 110 volt at the pushbuttons, cabinet base, air-operated dual chain hold-down vise. Fast, Low Cost Cutting of Hardened Tool Steel, Bars, Pipe, Angle Iron, Tubing, Flat Stock & Rod. Capacity: 3in solid • 6in Most Shapes • 30°- 45°—2.5in Most Solids • 4in Most Shapes Double Mitering Cutting Head can swivel 45° right or left of center. Indicators for 0°, 15°, 30° and 45°. Cutting head and pedestal are mounted on rugged swinging knee secured in lubricated for life bearings. Lock to hold desired cutting angle is quick and easy to operate.

Everett Everett_20-22OW Wet Cut-off Saw

Complete with 20 HP TEFC motor, magnetic starter with 110 volt at the pushbuttons, air operated V shaped chain hold-down vise, OSCILLATION, coolant tray, settling tank and pump Typical wet cutting speeds are 30 seconds per square inch of material based on application The cutting wheels on these Everett wet saw models are cooled by rotating through a water box with hinged adjustable sides. The water ejector and the wheel itself combine to throw the coolant into the cut and over the material to assure total cooling. The flow and discharge are easily regulated with the control valve and by adjusting the sides of the water box. Capacity: 3in solids. Most 7in shapes

Everett Everett_20-22W Wet Cut-off Saw

Complete with 20 HP TEFC motor, magnetic starter with 110 volt at the pushbuttons, air operated V shaped chain hold-down vise, OSCILLATION, coolant tray, settling tank and pump Typical wet cutting speeds are 30 seconds per square inch of material based on application The cutting wheels on these Everett wet saw models are cooled by rotating through a water box with hinged adjustable sides. The water ejector and the wheel itself combine to throw the coolant into the cut and over the material to assure total cooling. The flow and discharge are easily regulated with the control valve and by adjusting the sides of the water box. Capacity: 3in solids. Most 7in shapes

Everett Everett_26O Abrasive Cut-off Saw

Complete with 30 or 40 HP TEFC motor, magnetic starter with 110 volt at the pushbuttons, cabinet base and vise Exclusive vibra-action oscillation moves the wheel back and forth while cut is being made. This reduces the area of contact between the wheel and material, resulting in improved quality of cut, less heat build up, less burr and increased wheel life. Cutting of Hardened Tool Steel, Bars, Rounds, Shapes, Pipe, Angle Iron, Tubing, Flat Stock & Rod. Capacity: 6in solids. Most 7in Shapes

Everett Everett_26WO Wet Cut-off Saw

COMPLETE with 30 or 40 HP TEFC motor, magnetic starter with 110 volt at the pushbuttons, oscillation, air operated V shaped chain hold-down vise, coolant tray, settling tank and pump Exclusive vibra-action oscillation moves the wheel back and forth while cut is being made. This reduces the area of contact between the wheel and material, resulting in improved quality of cut, less heat build up, less burr and increased wheel life. Capacity: 5in solids. Most 7in Shapes Typical wet cutting saw speeds are 30 seconds per square inch of material based on application.